E-cigarette not producing vapour: what to do
You press the button and the screen lights up, but nothing comes out when you draw. Or perhaps your pod no longer reacts at all, with no light and no vapour. This is a common fault, and the cause is usually simple: a worn or insufficiently primed coil, a dirty contact, a battery that is too low or a setting that has changed. This guide takes you through the checks in order. Start with the symptom, then check the power supply, followed by the coil, the cartridge and the e-liquid. It is intended for adult vapers using a rechargeable kit, whether a box mod or a pod. No special tools are needed. If you have any doubts about the condition of the battery, the end of the article explains when to stop and how to dispose of a faulty device properly in Switzerland.
Contents
Quick diagnosis: start from the symptom
Before taking anything apart, look at how the device reacts. On-screen messages and the behaviour of the indicator light already tell you where the problem lies. Wording varies between manufacturers, so always refer to the manual for your model.
| Symptom | Likely cause | What to do |
|---|---|---|
| Nothing lights up | Flat battery or locked device | Recharge, then unlock |
| "No atomizer" or "Check atomizer" message | Coil or cartridge not detected | Screw it back in, clean the contacts, try another coil |
| "Short" or "Atomizer short" message | Short circuit in the coil or connector | Do not keep firing, replace the coil |
| "Low battery" message or flashing light | Not enough charge to heat | Recharge fully |
| The light comes on, little or no vapour | Worn coil, dry wick, power too low | Check the coil, the e-liquid level and the power |
| Auto-draw pod does not respond | Sensor blocked by condensation, cartridge not seated properly | Dry the contacts, reinsert the cartridge |
| Burnt taste and weak vapour | Dry cotton or coil at the end of its life | Stop, refill, wait or change the coil |
Battery, locking and connection
The device does not switch on
- Charge: connect the device using its cable and a charger in good condition, then let it charge for a while before trying again. A completely flat battery can take a few minutes to respond.
- Locking: many box mods and pods lock with a series of quick presses on the button, often five. Accidental locking in a pocket or bag is common.
- Removable batteries: if your box mod uses removable cells, check that they are inserted the right way round and that the wrap is intact. A torn wrap means the battery must be replaced.
The screen lights up, but nothing heats
In this case, the current is usually not reaching the coil. Unscrew the clearomiser or remove the cartridge, then wipe the box mod's connector and the base of the atomiser with a dry cloth or a cotton bud. A deposit of e-liquid or condensation is enough to break the contact. On a 510 connector, the small centre pin should protrude slightly. If it is pushed in, the contact will be poor. Then screw everything back together without forcing it, as overtightening can damage the thread. For a more thorough clean, follow our step-by-step guide to cleaning an e-cigarette, already published on this blog.
A worn or damaged battery
A battery that drains after a few puffs, displays "Low battery" just after charging or cuts out as soon as you draw is probably reaching the end of its life. If your model allows it, see our guide to changing the battery in your e-cigarette. However, a battery that is swollen, deformed, heats up abnormally or gives off an unusual smell must no longer be used or recharged. Cover the terminals with adhesive tape and take it to a shop or collection point. In Switzerland, the law requires shops to take back used batteries and rechargeable batteries free of charge, even without a new purchase, and requires consumers to return them. Used e-cigarettes are also covered.
Coil, cartridge and e-liquid
The coil
The coil is the most common cause of missing or very weak vapour. Coils have a limited lifespan. They gradually become clogged, especially with very sweet e-liquids, and eventually stop heating properly.
- New coil not yet primed: after a change, put a few drops of e-liquid on the visible cotton, fill the tank and wait a few minutes before vaping, starting at low power.
- Worn coil: a persistent burnt taste, a dull flavour or liquid that darkens quickly all mean the coil needs replacing. Our guide to changing your coil explains the procedure in detail.
- Wrong model: a coil from a different series may not be recognised, even if it looks similar. Check the exact compatible reference for your clearomiser in our range of coils.
- Value out of range: if the box mod displays an implausible ohm reading, or none at all, try another coil. If the reading remains inconsistent, the connector is at fault.
The pod cartridge
On pods, the cartridge is held in place by magnets or clips. Remove it and wipe the two gold contacts at the bottom of the slot and underneath the cartridge. Then refit it until it clicks into place. On auto-draw models, a sensor detects when you inhale, and condensation can block it. Remove the cartridge, blow gently into the slot or tap the device on a cloth, then leave it to dry. If the cartridge has a built-in coil, replace the whole cartridge when the vapour weakens.
E-liquid and settings
- Tank almost empty: when the level drops below the e-liquid inlets, the wick is no longer fed. Refill before reaching this point.
- Liquid too thick: an e-liquid high in vegetable glycerine flows slowly. Coils with small inlets, designed for a tight draw, will struggle to keep the wick fed. Choose a viscosity suited to your equipment. Our article on the different types of draw can help.
- Power too low or wrong mode: power that is too low for the coil produces barely visible vapour. Also check that the box mod has not been left in temperature control mode, which only works with certain coils.
- Airflow closed: an airflow ring turned by accident prevents you from drawing and, on an auto-draw pod, from triggering the sensor.
In summary
When an e-cigarette is not producing vapour, work through the checks in order: the charge and the lock first, then the contacts, then the coil or cartridge, and finally the e-liquid and settings. Most faults can be fixed in a few minutes with a dry cloth and a new, well-primed coil. The only exception is a damaged battery. In that case, do not attempt a repair. Take it back for disposal instead.
If the fault persists, you are welcome to bring your device to our shops in Cheseaux-sur-Lausanne and Villeneuve, where we will look into the problem with you. Coils and cartridges are also available from our online shop, with delivery from Cheseaux-sur-Lausanne.
Frequently asked questions
Why does my e-cigarette switch on without producing vapour?
Usually, the coil is worn, not screwed in properly or not recognised, or the contacts are dirty. Clean the connector, screw the coil back in or reinsert the cartridge, then try a new, well-primed coil. Also check the power setting and the e-liquid level.
How long should I wait after changing the coil?
After moistening the cotton and filling the tank, wait a few minutes so that the wick is fully saturated. Then start at low power. This prevents the cotton from burning on the first few puffs.
What should I do with a swollen battery or a faulty device?
Stop using it and do not recharge it. Cover the terminals with adhesive tape and take it to a shop or collection point. Shops that sell batteries and rechargeable batteries are required to take them back free of charge.
The sale of vaping products is restricted to adults (18 and over in Switzerland). Vaping is not intended for non-smokers.